The LSR6312SP powered subwoofer is based on a 12" woofer with JBLs patented neodymium Differential Drive and 260 Watts of power. An integral bass-management system provides all the features you need for todays multi-format surround production including: LCR and Direct LFE inputs, summed output for chaining multiple subwoofers, -4 dB alignment setting, and JBLs new RMC Room Mode Correction system. RMC Calibration Kit included. Features: Multiformat powered subwoofer Handling for Dolby Prologic, AC-3, DTS and other surround formats RMC Room Mode Correction controls response peaks due to room space RMC Calibration Kit included 250W continuous output power amplifier Sophisticated LCR bass management system Direct LFE input with selectable 10dB input sensitivity Summed output allows chaining of multiple units Neodymium Differential Drive NDD technology
Price: $1,529.00
LSR6332- Left Linear Spatial Reference Studio Monitor System The LSR6332 incorporates a 12" Differential Drive® dual coil woofer, 5" Kevlar midrange speaker and 1" titanium composite tweeter. Features: Advanced Linear Spatial Reference design ensures flatter response at the mix position. Differential Drive® technology with dynamic braking for extended low frequency response and low power compression. Neodymium midrange with 2" voice coil and Kevlar™ cone material for extended frequency response and low distortion. Titanium composite high frequency transducer with elliptical oblate spheroidal waveguide and damped polepiece. High-Density baffle for low enclosure resonance and stable inertial ground Linear Dynamics Aperture port design eliminates port turbulence and reduces port compression. Magnetically shielded for use near video monitors. Reinforced enclosure and convenient mounting points allow mounted installation.
Price: $1,419.00
LSR6332- Right Linear Spatial Reference Studio Monitor System The LSR6332 incorporates a 12" Differential Drive® dual coil woofer, 5" Kevlar midrange speaker and 1" titanium composite tweeter. Features: Advanced Linear Spatial Reference design ensures flatter response at the mix position. Differential Drive® technology with dynamic braking for extended low frequency response and low power compression. Neodymium midrange with 2" voice coil and Kevlar™ cone material for extended frequency response and low distortion. Titanium composite high frequency transducer with elliptical oblate spheroidal waveguide and damped polepiece. High-Density baffle for low enclosure resonance and stable inertial ground Linear Dynamics Aperture port design eliminates port turbulence and reduces port compression. Magnetically shielded for use near video monitors. Reinforced enclosure and convenient mounting points allow mounted installation.
Price: $1,419.00
The LSR6328P is THE choice for stereo and multichannel music and post audio applications where accuracy and high SPL are required. With ruler-flat +1 dB/-1.5 dB response from 50 Hz to 20 kHz, low frequency extension to 36 Hz, boundary compensation and JBLs new RMC system, the LSR6328P gives you exceptional low frequency performance in any room. The system is bi-amplified with a 250 Watt LF amplifier and a 120 Watt HF amplifier. Based around JBLs patented 8" Differential Drive® carbon-fiber woofer and a 1" titanium composite tweeter, the system produces smooth response and extraordinary SPL. Wall mounting provisions make the LSR6328P perfect for installation in multi-channel editorial rooms. Features: 250W low frequency amplifier 120W HF amplifier 8" low frequency driver 1" high frequency driver Advanced Linear Spatial Reference design ensures flatter-off-axis response for greater clarity at the mix position Room Mode Correction (RMC) User measurement and calibration kit available Differential Drive technology with dynamic braking for extended LF response and minimal power compression Integrated biamplification with factory calibrated sensitivities Titanium composite HF transducer with Elliptical Oblate Spheroidal waveguide for precise pattern control Magnetically shielded high-frequency transducer minimizes interference when used in close proximity to video monitors High-density baffle for low enclosure resonance
Price: $1,369.00
The FW-1884 is a professional DAW control surface and audio/MIDI interface that uses the Fire Wire high-speed data transfer protocol. With Fire Wires high-bandwidth capabilities, the FW-1884 provides audio and MIDI interfacing to computers as well as control of DAW parameters via eight 100mm motorized touch-sensitive channel faders, one master fader, and controls for pan, solo, mute and select functions on each channel. Tactile control for four bands of parametric EQ, a jog/shuttle wheel and a variety of shortcut keys for various popular software applications are also included. Co-designed by Tascam and Frontier Design Group, the FW-1884s DAW control capabilities include comprehensive mixing, automation, editing and navigation tools. Steinbergs Cubase LE in included free -- a 48-track, 96kHz professional recording workstation. An included application, Soft LCD, shows the assignment of the channel strip of your computer monitor. In addition to its surface control capabilities, the FW-1884 provides eight balanced XLR analog mic/line inputs with high quality mic preamps, phantom power and inserts on every channel. These mic preamps are the culmination of Tascams 30-year history of producing great-sounding, reliable equipment for home and professional studios alike. The mic input circuit uses a hybrid design combining the best of discrete and IC-based circuitry for 54dB of gain, wide dynamic range and natural response. The mic inputs have phantom power assignable in groups of four and include an analog insert on each channel for inserting outboard signal processing. The result is a clean preamp design with a frequency response of 20Hz to 40kHz (+0.5/-1.0dB) and a noise level of -124dBu(EIN), ideal for recording at 96kHz/24-bit resolution. For people who require simultaneous control of more audio channels, the FE-8 expands the FW-1884 with eight additional channel control strips (100mm motorized faders and dedicated control buttons). Up to 15 FE-8s may be added to an FW-1884 system as needed for big console functionality. Features: Comprehensive mixing, automation, editing and navigation tools for DAWs Eight 100mm motorized touch-sensitive channel faders, one motorized touch-sensitive master fader Dedicated controls for pan, solo, mute and select functions on each channel; tactile control for four bands of parametric EQ Shortcut keys for various popular audio software applications Eight balanced XLR analog mic/line inputs with high quality mic preamps Phantom power and inserts on every channel 24-bit/96kHz A/D and D/A converters; full 96kHz operation on all analog I/O channels with compatible DAW software Eight channels of ADAT light pipe, stereo S/PDIF inputs and outputs Eight analog outputs, allowing connection of L/R and 5.1 surround matrices Dedicated headphone output Four MIDI inputs, four MIDI outputs Word Clock in and out jacks Assignable foot switch jack Up to 18 simultaneous inputs Compatible with a wide variety of popular DAW applications Operates as a standalone 18x2 line mixer without a computer FE-8 (eight-channel sidecar) expands FW-1884 with eight additional channel control strips up to 128 channels (15 FE-8s). Soft LCD application simulates a scribble strip by displaying what each channel is controlling, see the screen shots in the column on the left Includes Cubase LE 48-track/96kHz recording and mixing software Includes GigaStudio 3 LE 64-voice streaming sampler software Compatible with MOTU Digital Performer, Apple Logic, Steinberg Cubase and Nuendo, and Cakewalk Sonar. Control surface compatible with Digidesign Pro Tools Dimensions: 22.9W x 5.4H x 18.9D Weight: 22.7 lbs Compatible with the latest Intel Macs
Price: $1,273.99
The RC-898 is the ultimate remote for the DTRS line. An LCD screen emulates the DA-98 display, offering a familiar interface for accessing functions. The complete remote control, the RC-898 can also access deeper functions like internal patchbays of the DA-38 and DA-98, as well as Confidence Monitoring mode of the DA-98. Time code registers and readouts make locating to specific timecode locations a snap. This top-of-the-line remote will keep you in the sweet spot where you belong! Features: Provides Transport, track arming, and locate points for 6 machines Dedicated function keys for 20 rapid access macros Self-Illuminating buttons make transport status obvious at a glance On board time registers Provides control over DA-98 Confidence Monitoring mode Provides control over DA-38 and DA-98 track copy and internal patchbays Large LCD screen emulates the familiar DA-98 interface Jog/Shuttle wheel Attaches to any Tascam DTRS machine through the DTRS Sync Port
Price: $1,269.10
SS-CDR1 The TASCAM SS-CDR1 combines Compact Flash and Compact Disc recording into a single rackspace. Designed for applications that previously used a cassette or MiniDisc recorder, the SS-CDR1 records in WAVE or MP3 formats to Compact Flash media. A slot-loading CD transport is provided CD recording, MP3 conversion and audio transfer. The recorder includes balanced and unbalanced audio inputs and outputs, RS-232 and parallel control and a wired remote control. Specifications: Solid state recoding to Compact Flash media CD-RW Recording and Playback One-rack-space compact design Records in WAVE or MP3 format to CF Card Balanced XLR and unbalanced RCA line input and output S/PDIF coaxial digital in and out with sample rate converter Power on play Auto track increment (level or time) PS/2 keyboard input for folder/file naming and remote control RS-232C serial control DB-25 parallel control port Dimensions (W x H x D): 483 x 44 x 300 (mm)
Price: $1,077.99
HD-R1 The HD-R1 Solid State Recorder is a two-channel, single rack-mount recording and playback device created with the sound contractor in mind. Specifications: Applicable Recording Media: Compact Flash Recording Format: WAV, MP3 Quantization: 16/24 bit liner, MP3 Sampling Frequency: 44.1/48/88.2/96kHz MIC/LINE INPUT Connector: XLR-3-31 (1: GND, 2: HOT, 3: COLD), balanced Euro Block Terminal, balanced LINE INPUT Connector: RCA, unbalanced LINE OUTPUTS Connector: XLR-3-31 (1: GND, 2: HOT, 3: HOT), balanced Euro Block Terminal, balanced Connector: RCA, unbalanced COAXIAL INPUT Connector: RCA Format: IEC60958-2 (S/PDIF) Quantization: 16/24-bit HEADPHONE OUTPUT Connector: 1/4" Stereo Phone Jack Serial Control Connector: D-Sub 9 pin Parallel Control COnnector: D-Sub 25 pin LAN Connector: RJ45 USB Connector: USB A-type
Price: $1,077.99
DV-W14R The new DV-W11R and DV-W14R are rackmount duplicators based on the same high-speed, reliable TEAC optical drives as TASCAM's current duplicators. The DV-W11R 1x1 duplicator is perfect for recording studios, houses of worship or anywhere else rackmounting is important. The DV-W14R includes a high-speed hard drive for saving disc images that can be written over and over. It has one master transport and four destination drives, and two can be chained together for 1x8 duplication. When the hard drive is used as a master source, the DV-W14R uses all five drives for writing new discs. All of the machines feature 12x TEAC DVD drives for fast, reliable duplication
Price: $979.99
RC-SS20 TASCAM's RC-SS20 is a remote control for the SS-R1, SS-CDR1 and HD-R1 solid-state recorders. A panel of 20 illuminated buttons provides instant access to tracks on TASCAM recorders. The RC-SS20 supports the Flash Play mode on the SS-R1 and SS-CDR1, so effects and announcements can be preloaded for instant playback. An "End Of Message" indicator shows when the end of the track is approaching. Specifications: Remote control for SS-R1, SS-CDR1 and HD-R1 20 Illuminated Buttons Supports Flash Play Mode on SS-R1, SS-CDR1 Load/Stop Button End Of Material indicator lights when end of track is approaching Includes 15' cable
Price: $891.79
Tascam 2488neo 24-Track Hard Disk Recorder Description: The 2488neo is TASCAM's latest take on its 24-track, 24-bit recorder. Sporting eight mic inputs, it's one of the few recorders able to record and mix a full band. A new batch of mastering effects joins the reverb, amp simulation, compression and EQ processing to create and burn finished-sounding CDs in a stand-alone unit. With TASCAM's simple interface, great-sounding preamps and chart-ready effects the 2488neo is the ultimate 24-track production machine. Features: New mastering effects include multiband compression, EQ and noise shaping for pro-sounding CD mixes 3-band EQ on 24 channels, 8-inputs and stereo bus with high and low sweepable shelving bands and full parametric mid band Three aux sends on all channels except the effects return Loop effect provides reverb, delay, chorus and more on an aux send and return Assignable Guitar multi-effects processor for overdrive, distortion, chorus, delay, flange and more Up to eight assignable dynamics processors for compression during recording or mixdown Dedicated Stereo Compressor on the stereo output Eight inputs: 4 XLR with phantom power double as 1/4" mic/line inputs, plus four more 1/4" mic/line inputs Nineteen 45mm faders including master fader LCD display for viewing meters and edit parameters 250 Virtual tracks CD-RW drive to record Audio CDs, import/export WAV files and backup hard drive High-speed USB 2.0 jack connects to PC or Mac® for data backup and SMF/WAV file Recording resolution: 44.1kHz, 16-bit or 24-bit
Price: $783.99
DVW/D13A/KIT TEAC's DVW/D13A/KIT/H 1x3 high-performance stand-alone duplicators come equipped with a 160GB hard-drive, are rich in features, and operate at true high-speed 16X when duplicating DVD discs. Specifications: Stand Alone 1x3, true 16x drives 160 GB Internal Hard Drive Record CD to CD-R at up to 48x speeds Switchable Voltage (115V AC or 220V AC) Multiple Eject Disc Mode - (Eject all, Eject good only, and Manual eject) Edit Track Function (CD Only) - CD to CD Edit or CD to HDD Edit Continuous copying - Cool-down periods not required No software or PC connection required User-friendly LCD Display menu Intelligent Auto Detection of DVD±R and DVD±RW media 17.25" x 7.5" x 18" (438.1 x 190.5 x 457.2 mm) 23.5 lbs (10.6 kg)
Price: $734.99
The Tascam FW-1082 Audio/MIDI Interface and Control Surface from Tascam and Frontier Design Group not only provides tons of audio and MIDI I/O to small studios, but offers a control surface with moving-faders for a previously unheard-of price. The FW-1082 features 10 inputs, including four balanced XLR mic inputs with phantom power. Two MIDI inputs and outputs are also included, plus S/PDIF digital I/O. Eight channel strips each feature a 60mm touch-sensitive moving fader and select/solo/mute buttons, and a moving master fader is also provided. The FW-1082 includes the latest Tascam software bundle: Cubase LE 96kHz/48-track recording software and GigaStudio 3 LE streaming sampler. The FW-1082 is a great choice for small studios, whether someone is just starting out or if theyre upgrading their equipment. Its four microphone inputs, two with analog insert jacks, have phantom power for professional condenser microphones. Four additional line inputs and a S/PDIF stereo input add up to 10 inputs simultaneously, each at 96kHz/24-bit audio resolution. Two MIDI inputs and outputs are provided for 32 channels of MIDI synth playback or control. The control surface has nine 60mm touch-sensitive moving faders for silky-smooth control over channel level, pan or aux settings. Four encoders are also available for mix control, as well as transport and jog/shuttle controls. Stereo monitoring is included, and the FW-1082 even mixes signals internally for stand-alone use. The FW-1082 includes Cubase LE professional 48-track, 96kHz recording and mixing software. It also includes GigaStudio 3 LE software sampling software, a 64-voice version of our groundbreaking streaming sampler. It works well with Steinberg Cubase and Nuendo , Apple Logic , Apple Final Cut Pro, Soundtrack Pro and Motion, Cakewalk Sonar , MOTU Digital Performer . It also works as a HUI control surface and MIDI interface for Digidesign Pro Tools . Features: 10-in/4-out audio interface at 96kHz/24-bit Nine 60mm touch-sensitive moving faders Four balanced XLR / 1/4 TRS mic/line inputs with phantom power Four balanced 1/4 TRS line inputs 1/4 TRS insert jacks for channels 1 & 2 S/PDIF stereo digital input and output Balanced 1/4 TRS monitor outputs Headphone output with level control Two MIDI inputs and outputs Assignable Footswitch jack Eight channel strips with solo, mute, select, record arm indicator Four assignable encoders control pan, aux level and EQ parameters Transport controls, jog/shuttle wheel, and many other surface controls Emulates Mackie HUI and Mackie Control in addition to the included native mode control plug ins Includes GigaStudio 3 LE Includes Steinberg Cubase LE 48-track 96kHz workstation software Dimensions: 19.1W x 3.25H x 15.2D Weight: 14.3 lbs. Compatible with the latest Intel Macs
Price: $587.99
SS-R1 The SS-R1 is TASCAM's affordable single-rack-space Compact Flash recorder for the installation market. Designed for applications that previously used a cassette or MiniDisc recorder, the SS-R1 records in WAVE or MP3 formats to Compact Flash media. The recorder includes balanced and unbalanced audio inputs and outputs, RS-232 and parallel control and a wired remote control. Specifications: Solid state recoding to Compact Flash media One-rack-space compact design Records in WAVE or MP3 format to CF Card Balanced XLR and unbalanced RCA line input and output S/PDIF coaxial digital in and out with sample rate converter Power on play Auto track increment (level or time) PS/2 keyboard input for folder/file naming and remote control RS-232C serial control DB-25 parallel control port Dimensions (W x H x D): 483 x 44 x 300 (mm)
Price: $587.99
BB-100CD The BB-1000 Portable CD/SD Recorder is built to make recording to CD as simple as pressing record on a cassette 'boom box.' The battery-powered recorder records to either SD Card media or blank CDs from four built-in microphones or XLR mic inputs. The two front and two back mics can be individually trimmed for a balanced recording, and tracks can be immediately played back through a built-in 10W sound system. The BB-1000CD has been designed for simple operation in schools, houses of worship and band rehearsal spaces. Specifications: Recording to CD-R/RW or SD/SDHC Memory Card Uncompressed PCM Recording (CD/SD) MP3 Recording (SD) Copy function dubs from SD to CD/ CD to SD Four Built-in High Quality Condenser Microphones for 360-degree recording Built-in 10W stereo Sound System Simple Operation with Dedicated Knobs and Keys Variable Speed Audition with Key Control Loop Playback Metronome and Chromatic tuner Over-dub recording Powered through 8 x AA Batteries or AC power adapter Wireless remote control unit included 2 x XLR mic inputs with +48V phantom power High-performance microphone preamp with 60dB of gain Premium AKM Audio4Pro A/D converters with over 100dB signal to noise ratio
Price: $587.99
Top Sellers
RC-30P For users of just about any TASCAM multitrack, the RC-30P is a wonderful timesaver. Punching in on recordings by hand means you're not ready to play right away. The RC-30P lets you play straight through. While automated punch-ins available on some recorders are also helpful, most punches can be done with the simple and efficient precision of the RC-30P, saving you time.
Price: $31.35
Copyright © 2010 Underbid, Inc. All Rights Reserved. Designated trademarks and brands are the property of their respective owners.
